The following chart lists the industry standards and specifications that apply to glass used in windows, doors, skylights and architectural glazing applications. Link astm c Active This link will 1c route to the current Active version of the standard. Glass Standards and Guidelines. Related Products Searching for related products This specification covers the quality requirements of flat, transparent, clear, and tinted glass intended astm c be used primarily for architectural glazing products.
Register or Log in for direct access to additional content. Cross sections of typical electrochromic windows are shown in which devices have four or five-layers of coatings that include the two or aatm active astm c sa Aatm standard does not purport to address all of the safety concerns, if any, associated with its use.
This specification covers the quality requirements for cut sizes of flat laminated glass consisting of two or more lites of glass bonded with an interlayer material for use in building glazing. This abstract is a brief summary of the referenced standard. Edge seal durability, internal moisture formation, internal volatile fog formation, argon gas retention.
How can I get samples to check your quantity? Medias this blog was made to help people to easily download or read PDF files. China acrylic frost China frosted glass film China freezer frost. Point blemish, linear blemish content, associated distortion, dimension, squareness, reflectance atm transmittance.
Historical Aatm s — view previous versions of standard. This standard does not purport to address all of the safety concerns, if any, associated with its use. Specifies the quality requirements for flat laminated glass consisting of two or more layers of glass bonded with an interlayer material. Work Item s — proposed revisions of this standard. Establishes the physical requirements for flat, heat strengthened, and fully tempered coated and uncoated glass.
This specification covers the quality requirements flat, transparent, clear, and tinted glass intended to be used primarily for architectural glazing asm. Glass strength, overall bow, localized bow, dimension, hole, notches and cut-out tolerances and product labeling. Experience — more than 20 years experiences on glass manufacturing and exporting. Hair, lint single strand light intensityD medium intensityE light intensityD medium intensityE medium intensityE medium intensityE Inside dirt dirt spot 1.
Lint-areas of concentrated lint light intensityD light intensityD light intensityD light intensityD light intensityD light intensityD Separation, discoloration none none none none none none B B B Short interlayer; unlaminated area chip CE 14 6.
The outer area is the area outside of the central area. B Not applicable. D Light IntensityBarely noticeable at 36 in. E Medium IntensityNoticeable at 36 in. Nominal thickness tolerance computation guidelines are as 8. The deviation from flatness of laminated glass depends on 8. For other than annealed transparent glasses the the maximum thickness of each glass ply obtained from overall bow and warp shall not exceed the values shown in Specification C and the maximum interlayer thickness Table 3 when measured in accordance with 7.
Keywords 8. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and if not revised, either reapproved or withdrawn.
Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phone , fax , or service astm.
Open navigation menu. Close suggestions Search Search. User Settings. Skip carousel. Carousel Previous. Carousel Next. What is Scribd? Uploaded by Ryler Vin. Did you find this document useful? Is this content inappropriate? Point blemish, linear blemish content, associated distortion, dimension, squareness, wstm and transmittance. Cookies are small files stored in your browser and are used by most websites to improve your overall experience.
Yes, we have a professional technique team, OEM accept. The following test methods shall be performed to meet the specified requirements: Can you do the production as customized?
Referenced Documents purchase separately The documents listed below ast referenced within the subject standard but are not provided as part of the standard. Size up awtm 25 Sf. Historical Version s — view previous versions of standard. How can I get samples to check your quantity? The following test methods shall be x to meet the specified requirements:.
This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website. We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent.
0コメント